openSUSE Build Service

Overview Repositories Revisions Requests Users Attributes Meta

File lvm.conf of Package lvm2-clvm (Revision ea5a4ff2e9449564cce87fa2bce8e4b2)

Currently displaying revision ea5a4ff2e9449564cce87fa2bce8e4b2 , Show latest

# This is an example configuration file for the LVM2 system.
# It contains the default settings that would be used if there was no
# /etc/lvm/lvm.conf file.
#
# Refer to 'man lvm.conf' for further information including the file layout.
#
# To put this file in a different directory and override /etc/lvm set
# the environment variable LVM_SYSTEM_DIR before running the tools.
#
# N.B. Take care that each setting only appears once if uncommenting
# example settings in this file.

# This section allows you to set the way the configuration settings are handled.
config {

# If enabled, any LVM2 configuration mismatch is reported.
	# This implies checking that the configuration key is understood
	# by LVM2 and that the value of the key is of a proper type.
	# If disabled, any configuration mismatch is ignored and default
	# value is used instead without any warning (a message about the
	# configuration key not being found is issued in verbose mode only).
	checks = 1

# If enabled, any configuration mismatch aborts the LVM2 process.
	abort_on_errors = 0

# Directory where LVM looks for configuration profiles.
	profile_dir = "/etc/lvm/profile"
}

# This section allows you to configure which block devices should
# be used by the LVM system.
devices {

# Where do you want your volume groups to appear ?
	dir = "/dev"

# An array of directories that contain the device nodes you wish
	# to use with LVM2.
	scan = [ "/dev" ]

# If set, the cache of block device nodes with all associated symlinks
	# will be constructed out of the existing udev database content.
	# This avoids using and opening any inapplicable non-block devices or
	# subdirectories found in the device directory. This setting is applied
	# to udev-managed device directory only, other directories will be scanned
	# fully. LVM2 needs to be compiled with udev support for this setting to
	# take effect. N.B. Any device node or symlink not managed by udev in
	# udev directory will be ignored with this setting on.
	obtain_device_list_from_udev = 1

# If several entries in the scanned directories correspond to the
	# same block device and the tools need to display a name for device,
	# all the pathnames are matched against each item in the following
	# list of regular expressions in turn and the first match is used.

# By default no preferred names are defined.
	# preferred_names = [ ]

# Try to avoid using undescriptive /dev/dm-N names, if present.
	# preferred_names = [ "^/dev/mpath/", "^/dev/mapper/mpath", "^/dev/[hs]d" ]

# In case no prefererred name matches or if preferred_names are not
	# defined at all, builtin rules are used to determine the preference.
	#
	# The first builtin rule checks path prefixes and it gives preference
	# based on this ordering (where "dev" depends on devices/dev setting):
	#	/dev/mapper > /dev/disk > /dev/dm-* > /dev/block
	#
	# If the ordering above cannot be applied, the path with fewer slashes
	# gets preference then.
	#
	# If the number of slashes is the same, a symlink gets preference.
	#
	# Finally, if all the rules mentioned above are not applicable,
	# lexicographical order is used over paths and the smallest one
	# of all gets preference.

# A filter that tells LVM2 to only use a restricted set of devices.
	# The filter consists of an array of regular expressions.  These
	# expressions can be delimited by a character of your choice, and
	# prefixed with either an 'a' (for accept) or 'r' (for reject).
	# The first expression found to match a device name determines if
	# the device will be accepted or rejected (ignored).  Devices that
	# don't match any patterns are accepted.

# Be careful if there there are symbolic links or multiple filesystem 
	# entries for the same device as each name is checked separately against
	# the list of patterns.  The effect is that if the first pattern in the 
	# list to match a name is an 'a' pattern for any of the names, the device
	# is accepted; otherwise if the first pattern in the list to match a name
	# is an 'r' pattern for any of the names it is rejected; otherwise it is
	# accepted.

# By default we accept every block device except udev names, floppy and cdrom drives:
	filter = [ "r|/dev/.*/by-path/.*|", "r|/dev/.*/by-id/.*|", "r|/dev/fd.*|", "r|/dev/cdrom|", "a/.*/" ]

# Exclude the cdrom drive
	# filter = [ "r|/dev/cdrom|" ]

# When testing I like to work with just loopback devices:
	# filter = [ "a/loop/", "r/.*/" ]

# Or maybe all loops and ide drives except hdc:
	# filter =[ "a|loop|", "r|/dev/hdc|", "a|/dev/ide|", "r|.*|" ]

# Use anchors if you want to be really specific
	# filter = [ "a|^/dev/hda8$|", "r/.*/" ]

# Since "filter" is often overridden from command line, it is not suitable
	# for system-wide device filtering (udev rules, lvmetad). To hide devices
	# from LVM-specific udev processing and/or from lvmetad, you need to set
	# global_filter. The syntax is the same as for normal "filter"
	# above. Devices that fail the global_filter are not even opened by LVM.

# global_filter = []

# The results of the filtering are cached on disk to avoid
	# rescanning dud devices (which can take a very long time).
	# By default this cache is stored in the /etc/lvm/cache directory
	# in a file called '.cache'.
	# It is safe to delete the contents: the tools regenerate it.
	# (The old setting 'cache' is still respected if neither of
	# these new ones is present.)
	# N.B. If obtain_device_list_from_udev is set to 1 the list of
	# devices is instead obtained from udev and any existing .cache
	# file is removed.
	cache_dir = "/etc/lvm/cache"
	cache_file_prefix = ""

# You can turn off writing this cache file by setting this to 0.
	write_cache_state = 1

# Advanced settings.

# List of pairs of additional acceptable block device types found 
	# in /proc/devices with maximum (non-zero) number of partitions.
	# types = [ "fd", 16 ]

# If sysfs is mounted (2.6 kernels) restrict device scanning to 
	# the block devices it believes are valid.
	# 1 enables; 0 disables.
	sysfs_scan = 1

# By default, LVM2 will ignore devices used as component paths
	# of device-mapper multipath devices.
	# 1 enables; 0 disables.
	multipath_component_detection = 1

# By default, LVM2 will ignore devices used as components of
	# software RAID (md) devices by looking for md superblocks.
	# 1 enables; 0 disables.
	md_component_detection = 1

# By default, if a PV is placed directly upon an md device, LVM2
	# will align its data blocks with the md device's stripe-width.
	# 1 enables; 0 disables.
	md_chunk_alignment = 1

# Default alignment of the start of a data area in MB.	If set to 0,
	# a value of 64KB will be used.  Set to 1 for 1MiB, 2 for 2MiB, etc.
	# default_data_alignment = 1

# By default, the start of a PV's data area will be a multiple of
	# the 'minimum_io_size' or 'optimal_io_size' exposed in sysfs.
	# - minimum_io_size - the smallest request the device can perform
	#	w/o incurring a read-modify-write penalty (e.g. MD's chunk size)
	# - optimal_io_size - the device's preferred unit of receiving I/O
	#	(e.g. MD's stripe width)
	# minimum_io_size is used if optimal_io_size is undefined (0).
	# If md_chunk_alignment is enabled, that detects the optimal_io_size.
	# This setting takes precedence over md_chunk_alignment.
	# 1 enables; 0 disables.
	data_alignment_detection = 1

# Alignment (in KB) of start of data area when creating a new PV.
	# md_chunk_alignment and data_alignment_detection are disabled if set.
	# Set to 0 for the default alignment (see: data_alignment_default)
	# or page size, if larger.
	data_alignment = 0

# By default, the start of the PV's aligned data area will be shifted by
	# the 'alignment_offset' exposed in sysfs.	This offset is often 0 but
	# may be non-zero; e.g.: certain 4KB sector drives that compensate for
	# windows partitioning will have an alignment_offset of 3584 bytes
	# (sector 7 is the lowest aligned logical block, the 4KB sectors start
	# at LBA -1, and consequently sector 63 is aligned on a 4KB boundary).
	# But note that pvcreate --dataalignmentoffset will skip this detection.
	# 1 enables; 0 disables.
	data_alignment_offset_detection = 1

# If, while scanning the system for PVs, LVM2 encounters a device-mapper
	# device that has its I/O suspended, it waits for it to become accessible.
	# Set this to 1 to skip such devices.  This should only be needed
	# in recovery situations.
	ignore_suspended_devices = 0

# ignore_lvm_mirrors:  Introduced in version 2.02.104
	# This setting determines whether logical volumes of "mirror" segment
	# type are scanned for LVM labels.	This affects the ability of
	# mirrors to be used as physical volumes.  If 'ignore_lvm_mirrors'
	# is set to '1', it becomes impossible to create volume groups on top
	# of mirror logical volumes - i.e. to stack volume groups on mirrors.
	#
	# Allowing mirror logical volumes to be scanned (setting the value to '0')
	# can potentially cause LVM processes and I/O to the mirror to become
	# blocked.	This is due to the way that the "mirror" segment type handles
	# failures.  In order for the hang to manifest itself, an LVM command must
	# be run just after a failure and before the automatic LVM repair process
	# takes place OR there must be failures in multiple mirrors in the same
	# volume group at the same time with write failures occurring moments
	# before a scan of the mirror's labels.
	#
	# Note that these scanning limitations do not apply to the LVM RAID
	# types, like "raid1".	The RAID segment types handle failures in a
	# different way and are not subject to possible process or I/O blocking.
	#
	# It is encouraged that users set 'ignore_lvm_mirrors' to 1 if they
	# are using the "mirror" segment type.	Users that require volume group
	# stacking on mirrored logical volumes should consider using the "raid1"
	# segment type.  The "raid1" segment type is not available for
	# active/active clustered volume groups.
	#
	# Set to 1 to disallow stacking and thereby avoid a possible deadlock.
	ignore_lvm_mirrors = 1

# During each LVM operation errors received from each device are counted.
	# If the counter of a particular device exceeds the limit set here, no
	# further I/O is sent to that device for the remainder of the respective
	# operation. Setting the parameter to 0 disables the counters altogether.
	disable_after_error_count = 0

# Allow use of pvcreate --uuid without requiring --restorefile.
	require_restorefile_with_uuid = 1

# Minimum size (in KB) of block devices which can be used as PVs.
	# In a clustered environment all nodes must use the same value.
	# Any value smaller than 512KB is ignored.

# Ignore devices smaller than 2MB such as floppy drives.
	pv_min_size = 2048

# The original built-in setting was 512 up to and including version 2.02.84.
	# pv_min_size = 512

# Issue discards to a logical volumes's underlying physical volume(s) when
	# the logical volume is no longer using the physical volumes' space (e.g.
	# lvremove, lvreduce, etc).  Discards inform the storage that a region is
	# no longer in use.  Storage that supports discards advertise the protocol
	# specific way discards should be issued by the kernel (TRIM, UNMAP, or
	# WRITE SAME with UNMAP bit set).  Not all storage will support or benefit
	# from discards but SSDs and thinly provisioned LUNs generally do.	If set
	# to 1, discards will only be issued if both the storage and kernel provide
	# support.
	# 1 enables; 0 disables.
	issue_discards = 0
}

# This section allows you to configure the way in which LVM selects
# free space for its Logical Volumes.
allocation {

# When searching for free space to extend an LV, the "cling"
	# allocation policy will choose space on the same PVs as the last
	# segment of the existing LV.  If there is insufficient space and a
	# list of tags is defined here, it will check whether any of them are
	# attached to the PVs concerned and then seek to match those PV tags
	# between existing extents and new extents.
	# Use the special tag "@*" as a wildcard to match any PV tag.
 
	# Example: LVs are mirrored between two sites within a single VG.
	# PVs are tagged with either @site1 or @site2 to indicate where
	# they are situated.

# cling_tag_list = [ "@site1", "@site2" ]
	# cling_tag_list = [ "@*" ]

# Changes made in version 2.02.85 extended the reach of the 'cling'
	# policies to detect more situations where data can be grouped
	# onto the same disks.	Set this to 0 to revert to the previous
	# algorithm.
	maximise_cling = 1

# Whether to use blkid library instead of native LVM2 code to detect
	# any existing signatures while creating new Physical Volumes and
	# Logical Volumes. LVM2 needs to be compiled with blkid wiping support
	# for this setting to take effect.
	#
	# LVM2 native detection code is currently able to recognize these signatures:
	#	- MD device signature
	#	- swap signature
	#	- LUKS signature
	# To see the list of signatures recognized by blkid, check the output
	# of 'blkid -k' command. The blkid can recognize more signatures than
	# LVM2 native detection code, but due to this higher number of signatures
	# to be recognized, it can take more time to complete the signature scan.
	use_blkid_wiping = 1

# Set to 1 to wipe any signatures found on newly-created Logical Volumes
	# automatically in addition to zeroing of the first KB on the LV
	# (controlled by the -Z/--zero y option).
	# The command line option -W/--wipesignatures takes precedence over this
	# setting.
	# The default is to wipe signatures when zeroing.
	#
	wipe_signatures_when_zeroing_new_lvs = 1

# Set to 1 to guarantee that mirror logs will always be placed on 
	# different PVs from the mirror images.  This was the default
	# until version 2.02.85.
	mirror_logs_require_separate_pvs = 0

# Set to 1 to guarantee that cache_pool metadata will always be
	# placed on  different PVs from the cache_pool data.
	cache_pool_metadata_require_separate_pvs = 0

# Specify the minimal chunk size (in kiB) for cache pool volumes.
	# Using a chunk_size that is too large can result in wasteful use of
	# the cache, where small reads and writes can cause large sections of
	# an LV to be mapped into the cache.  However, choosing a chunk_size
	# that is too small can result in more overhead trying to manage the
	# numerous chunks that become mapped into the cache.  The former is
	# more of a problem than the latter in most cases, so we default to
	# a value that is on the smaller end of the spectrum.  Supported values
	# range from 32(kiB) to 1048576 in multiples of 32.
	# cache_pool_chunk_size = 64

# Set to 1 to guarantee that thin pool metadata will always
	# be placed on different PVs from the pool data.
	thin_pool_metadata_require_separate_pvs = 0

# Specify chunk size calculation policy for thin pool volumes.
	# Possible options are:
	# "generic"		   - if thin_pool_chunk_size is defined, use it.
	#					 Otherwise, calculate the chunk size based on
	#					 estimation and device hints exposed in sysfs:
	#					 the minimum_io_size. The chunk size is always
	#					 at least 64KiB.
	#
	# "performance"    - if thin_pool_chunk_size is defined, use it.
	#			 Otherwise, calculate the chunk size for
	#			 performance based on device hints exposed in
	#			 sysfs: the optimal_io_size. The chunk size is
	#			 always at least 512KiB.
	# thin_pool_chunk_size_policy = "generic"

# Specify the minimal chunk size (in KB) for thin pool volumes.
	# Use of the larger chunk size may improve performance for plain
	# thin volumes, however using them for snapshot volumes is less efficient,
	# as it consumes more space and takes extra time for copying.
	# When unset, lvm tries to estimate chunk size starting from 64KB
	# Supported values are in range from 64 to 1048576.
	# thin_pool_chunk_size = 64

# Specify discards behaviour of the thin pool volume.
	# Select one of  "ignore", "nopassdown", "passdown"
	# thin_pool_discards = "passdown"

# Set to 0, to disable zeroing of thin pool data chunks before their
	# first use.
	# N.B. zeroing larger thin pool chunk size degrades performance.
	# thin_pool_zero = 1
}

# This section that allows you to configure the nature of the
# information that LVM2 reports.
log {

# Controls the messages sent to stdout or stderr.
	# There are three levels of verbosity, 3 being the most verbose.
	verbose = 0

# Set to 1 to suppress all non-essential messages from stdout.
	# This has the same effect as -qq.
	# When this is set, the following commands still produce output:
	# dumpconfig, lvdisplay, lvmdiskscan, lvs, pvck, pvdisplay, 
	# pvs, version, vgcfgrestore -l, vgdisplay, vgs.
	# Non-essential messages are shifted from log level 4 to log level 5
	# for syslog and lvm2_log_fn purposes.
	# Any 'yes' or 'no' questions not overridden by other arguments
	# are suppressed and default to 'no'.
	silent = 0

# Should we send log messages through syslog?
	# 1 is yes; 0 is no.
	syslog = 1

# Should we log error and debug messages to a file?
	# By default there is no log file.
	#file = "/var/log/lvm2.log"

# Should we overwrite the log file each time the program is run?
	# By default we append.
	overwrite = 0

# What level of log messages should we send to the log file and/or syslog?
	# There are 6 syslog-like log levels currently in use - 2 to 7 inclusive.
	# 7 is the most verbose (LOG_DEBUG).
	level = 0

# Format of output messages
	# Whether or not (1 or 0) to indent messages according to their severity
	indent = 1

# Whether or not (1 or 0) to display the command name on each line output
	command_names = 0

# A prefix to use before the message text (but after the command name,
	# if selected).  Default is two spaces, so you can see/grep the severity
	# of each message.
	prefix = "	"

# To make the messages look similar to the original LVM tools use:
	#	indent = 0
	#	command_names = 1
	#	prefix = " -- "

# Set this if you want log messages during activation.
	# Don't use this in low memory situations (can deadlock).
	# activation = 0

# Some debugging messages are assigned to a class and only appear
	# in debug output if the class is listed here.
	# Classes currently available:
	#	memory, devices, activation, allocation, lvmetad, metadata, cache,
	#	locking
	# Use "all" to see everything.
	debug_classes = [ "memory", "devices", "activation", "allocation", "lvmetad", "metadata", "cache", "locking" ]
}

# Configuration of metadata backups and archiving.	In LVM2 when we
# talk about a 'backup' we mean making a copy of the metadata for the
# *current* system.  The 'archive' contains old metadata configurations.
# Backups are stored in a human readable text format.
backup {

# Should we maintain a backup of the current metadata configuration ?
	# Use 1 for Yes; 0 for No.
	# Think very hard before turning this off!
	backup = 1

# Where shall we keep it ?
	# Remember to back up this directory regularly!
	backup_dir = "/etc/lvm/backup"

# Should we maintain an archive of old metadata configurations.
	# Use 1 for Yes; 0 for No.
	# On by default.  Think very hard before turning this off.
	archive = 1

# Where should archived files go ?
	# Remember to back up this directory regularly!
	archive_dir = "/etc/lvm/archive"

# What is the minimum number of archive files you wish to keep ?
	retain_min = 10

# What is the minimum time you wish to keep an archive file for ?
	retain_days = 30
}

# Settings for the running LVM2 in shell (readline) mode.
shell {

# Number of lines of history to store in ~/.lvm_history
	history_size = 100
}

# Miscellaneous global LVM2 settings
global {
	# The file creation mask for any files and directories created.
	# Interpreted as octal if the first digit is zero.
	umask = 077

# Allow other users to read the files
	#umask = 022

# Enabling test mode means that no changes to the on disk metadata
	# will be made.  Equivalent to having the -t option on every
	# command.	Defaults to off.
	test = 0

# Default value for --units argument
	units = "h"

# Since version 2.02.54, the tools distinguish between powers of
	# 1024 bytes (e.g. KiB, MiB, GiB) and powers of 1000 bytes (e.g.
	# KB, MB, GB).
	# If you have scripts that depend on the old behaviour, set this to 0
	# temporarily until you update them.
	si_unit_consistency = 1

# Whether or not to display unit suffix for sizes. This setting has
	# no effect if the units are in human-readable form (global/units="h")
	# in which case the suffix is always displayed.
	suffix = 1

# Whether or not to communicate with the kernel device-mapper.
	# Set to 0 if you want to use the tools to manipulate LVM metadata 
	# without activating any logical volumes.
	# If the device-mapper kernel driver is not present in your kernel
	# setting this to 0 should suppress the error messages.
	activation = 1

# If we can't communicate with device-mapper, should we try running 
	# the LVM1 tools?
	# This option only applies to 2.4 kernels and is provided to help you
	# switch between device-mapper kernels and LVM1 kernels.
	# The LVM1 tools need to be installed with .lvm1 suffices
	# e.g. vgscan.lvm1 and they will stop working after you start using
	# the new lvm2 on-disk metadata format.
	# The default value is set when the tools are built.
	# fallback_to_lvm1 = 0

# The default metadata format that commands should use - "lvm1" or "lvm2".
	# The command line override is -M1 or -M2.
	# Defaults to "lvm2".
	# format = "lvm2"

# Location of proc filesystem
	proc = "/proc"

# Type of locking to use. Defaults to local file-based locking (1).
	# Turn locking off by setting to 0 (dangerous: risks metadata corruption
	# if LVM2 commands get run concurrently).
	# Type 2 uses the external shared library locking_library.
	# Type 3 uses built-in clustered locking.
	# Type 4 uses read-only locking which forbids any operations that might 
	# change metadata.
	# Type 5 offers dummy locking for tools that do not need any locks.
	# You should not need to set this directly: the tools will select when
	# to use it instead of the configured locking_type.  Do not use lvmetad or
	# the kernel device-mapper driver with this locking type.
	# It is used by the --readonly option that offers read-only access to
	# Volume Group metadata that cannot be locked safely because it belongs to
	# an inaccessible domain and might be in use, for example a virtual machine
	# image or a disk that is shared by a clustered machine.  
	#
	# N.B. Don't use lvmetad with locking type 3 as lvmetad is not yet
	# supported in clustered environment. If use_lvmetad=1 and locking_type=3
	# is set at the same time, LVM always issues a warning message about this
	# and then it automatically disables lvmetad use.
	locking_type = 1

# Set to 0 to fail when a lock request cannot be satisfied immediately.
	wait_for_locks = 1

# If using external locking (type 2) and initialisation fails,
	# with this set to 1 an attempt will be made to use the built-in
	# clustered locking.
	# If you are using a customised locking_library you should set this to 0.
	fallback_to_clustered_locking = 1

# If an attempt to initialise type 2 or type 3 locking failed, perhaps
	# because cluster components such as clvmd are not running, with this set
	# to 1 an attempt will be made to use local file-based locking (type 1).
	# If this succeeds, only commands against local volume groups will proceed.
	# Volume Groups marked as clustered will be ignored.
	fallback_to_local_locking = 1

# Local non-LV directory that holds file-based locks while commands are
	# in progress.	A directory like /tmp that may get wiped on reboot is OK.
	locking_dir = "/run/lvm/lock"

# Whenever there are competing read-only and read-write access requests for
	# a volume group's metadata, instead of always granting the read-only
	# requests immediately, delay them to allow the read-write requests to be
	# serviced.  Without this setting, write access may be stalled by a high
	# volume of read-only requests.
	# NB. This option only affects locking_type = 1 viz. local file-based
	# locking.
	prioritise_write_locks = 1

# Other entries can go here to allow you to load shared libraries
	# e.g. if support for LVM1 metadata was compiled as a shared library use
	#	format_libraries = "liblvm2format1.so" 
	# Full pathnames can be given.

# Search this directory first for shared libraries.
	#	library_dir = "/lib"

# The external locking library to load if locking_type is set to 2.
	#	locking_library = "liblvm2clusterlock.so"

# Treat any internal errors as fatal errors, aborting the process that
	# encountered the internal error. Please only enable for debugging.
	abort_on_internal_errors = 0

# Check whether CRC is matching when parsed VG is used multiple times.
	# This is useful to catch unexpected internal cached volume group
	# structure modification. Please only enable for debugging.
	detect_internal_vg_cache_corruption = 0

# If set to 1, no operations that change on-disk metadata will be permitted.
	# Additionally, read-only commands that encounter metadata in need of repair
	# will still be allowed to proceed exactly as if the repair had been 
	# performed (except for the unchanged vg_seqno).
	# Inappropriate use could mess up your system, so seek advice first!
	metadata_read_only = 0

# 'mirror_segtype_default' defines which segtype will be used when the
	# shorthand '-m' option is used for mirroring.	The possible options are:
	#
	# "mirror" - The original RAID1 implementation provided by LVM2/DM.  It is
	#			 characterized by a flexible log solution (core, disk, mirrored)
	#		 and by the necessity to block I/O while reconfiguring in the
	#		 event of a failure.
	#
	#		 There is an inherent race in the dmeventd failure handling
	#		 logic with snapshots of devices using this type of RAID1 that
	#		 in the worst case could cause a deadlock.
	#		   Ref: https://bugzilla.redhat.com/show_bug.cgi?id=817130#c10
	#
	# "raid1"  - This implementation leverages MD's RAID1 personality through
	#			 device-mapper.  It is characterized by a lack of log options.
	#		 (A log is always allocated for every device and they are placed
	#		 on the same device as the image - no separate devices are
	#		 required.)  This mirror implementation does not require I/O
	#		 to be blocked in the kernel in the event of a failure.
	#		 This mirror implementation is not cluster-aware and cannot be
	#		 used in a shared (active/active) fashion in a cluster.
	#
	# Specify the '--type <mirror|raid1>' option to override this default
	# setting.
	mirror_segtype_default = "raid1"

# 'raid10_segtype_default' determines the segment types used by default
	# when the '--stripes/-i' and '--mirrors/-m' arguments are both specified
	# during the creation of a logical volume.
	# Possible settings include:
	#
	# "raid10" - This implementation leverages MD's RAID10 personality through
	#			 device-mapper.
	#
	# "mirror" - LVM will layer the 'mirror' and 'stripe' segment types.  It
	#			 will do this by creating a mirror on top of striped sub-LVs;
	#			 effectively creating a RAID 0+1 array.  This is suboptimal
	#			 in terms of providing redundancy and performance. Changing to
	#			 this setting is not advised.
	# Specify the '--type <raid10|mirror>' option to override this default
	# setting.
	raid10_segtype_default = "raid10"

# The default format for displaying LV names in lvdisplay was changed 
	# in version 2.02.89 to show the LV name and path separately.
	# Previously this was always shown as /dev/vgname/lvname even when that
	# was never a valid path in the /dev filesystem.
	# Set to 1 to reinstate the previous format.
	#
	# lvdisplay_shows_full_device_path = 0

# Whether to use (trust) a running instance of lvmetad. If this is set to
	# 0, all commands fall back to the usual scanning mechanisms. When set to 1
	# *and* when lvmetad is running (automatically instantiated by making use of
	# systemd's socket-based service activation or run as an initscripts service
	# or run manually), the volume group metadata and PV state flags are obtained
	# from the lvmetad instance and no scanning is done by the individual
	# commands. In a setup with lvmetad, lvmetad udev rules *must* be set up for
	# LVM to work correctly. Without proper udev rules, all changes in block
	# device configuration will be *ignored* until a manual 'pvscan --cache'
	# is performed. These rules are installed by default.
	#
	# If lvmetad has been running while use_lvmetad was 0, it MUST be stopped
	# before changing use_lvmetad to 1 and started again afterwards.
	#
	# If using lvmetad, the volume activation is also switched to automatic
	# event-based mode. In this mode, the volumes are activated based on
	# incoming udev events that automatically inform lvmetad about new PVs
	# that appear in the system. Once the VG is complete (all the PVs are
	# present), it is auto-activated. The activation/auto_activation_volume_list
	# setting controls which volumes are auto-activated (all by default).
	#
	# A note about device filtering while lvmetad is used:
	# When lvmetad is updated (either automatically based on udev events
	# or directly by pvscan --cache <device> call), the devices/filter
	# is ignored and all devices are scanned by default. The lvmetad always
	# keeps unfiltered information which is then provided to LVM commands
	# and then each LVM command does the filtering based on devices/filter
	# setting itself.
	# To prevent scanning devices completely, even when using lvmetad,
	# the devices/global_filter must be used.
	# N.B. Don't use lvmetad with locking type 3 as lvmetad is not yet
	# supported in clustered environment. If use_lvmetad=1 and locking_type=3
	# is set at the same time, LVM always issues a warning message about this
	# and then it automatically disables lvmetad use.
	# If use_lvmetad set to 1, please make sure lvm2-lvmetad.socket is started
	use_lvmetad = 1

# Configuration option global/use_lvmlockd.
	# Use lvmlockd for locking among hosts using LVM on shared storage.
	# Applicable only if LVM is compiled with lockd support in which
	# case there is also lvmlockd(8) man page available for more
	# information.
	use_lvmlockd = 0

# Configuration option global/lvmlockd_lock_retries.
	# Retry lvmlockd lock requests this many times.
	# Applicable only if LVM is compiled with lockd support
	# This configuration option has an automatic default value.
	# lvmlockd_lock_retries = 3

# Configuration option global/sanlock_lv_extend.
	# Size in MiB to extend the internal LV holding sanlock locks.
	# The internal LV holds locks for each LV in the VG, and after enough
	# LVs have been created, the internal LV needs to be extended. lvcreate
	# will automatically extend the internal LV when needed by the amount
	# specified here. Setting this to 0 disables the automatic extension
	# and can cause lvcreate to fail. Applicable only if LVM is compiled
	# with lockd support
	# This configuration option has an automatic default value.
	# sanlock_lv_extend = 256

# Full path of the utility called to check that a thin metadata device
	# is in a state that allows it to be used.
	# Each time a thin pool needs to be activated or after it is deactivated
	# this utility is executed. The activation will only proceed if the utility
	# has an exit status of 0.
	# Set to "" to skip this check.  (Not recommended.)
	# The thin tools are available as part of the device-mapper-persistent-data
	# package from https://github.com/jthornber/thin-provisioning-tools.
	#
	# thin_check_executable = "/usr/sbin/thin_check"

# Array of string options passed with thin_check command. By default,
	# option "-q" is for quiet output.
	# With thin_check version 2.1 or newer you can add "--ignore-non-fatal-errors"
	# to let it pass through ignorable errors and fix them later.
	# With thin_check version 3.2 or newer you should add
	# "--clear-needs-check-flag".
	#
	# thin_check_options = [ "-q", "--clear-needs-check-flag" ]

# Full path of the utility called to repair a thin metadata device
	# is in a state that allows it to be used.
	# Each time a thin pool needs repair this utility is executed.
	# See thin_check_executable how to obtain binaries.
	#
	# thin_repair_executable = "/usr/sbin/thin_repair"

# Array of extra string options passed with thin_repair command.
	# thin_repair_options = [ "" ]

# Full path of the utility called to dump thin metadata content.
	# See thin_check_executable how to obtain binaries.
	#
	# thin_dump_executable = "/usr/sbin/thin_dump"

# If set, given features are not used by thin driver.
	# This can be helpful not just for testing, but i.e. allows to avoid
	# using problematic implementation of some thin feature.
	# Features:
	#	block_size
	#	discards
	#	discards_non_power_2
	#	external_origin
	#	metadata_resize
	#	external_origin_extend
	#
	# thin_disabled_features = [ "discards", "block_size" ]

# Full path of the utility called to check that a cache metadata device
	# is in a state that allows it to be used.
	# Each time a cached LV needs to be used or after it is deactivated
	# this utility is executed. The activation will only proceed if the utility
	# has an exit status of 0.
	# Set to "" to skip this check.  (Not recommended.)
	# The cache tools are available as part of the device-mapper-persistent-data
	# package from https://github.com/jthornber/thin-provisioning-tools.
	#
	# cache_check_executable = "autodetect"

# Array of string options passed with cache_check command. By default,
	# option "-q" is for quiet output.
	#
	# cache_check_options = [ "-q" ]

# Full path of the utility called to repair a cache metadata device.
	# Each time a cache metadata needs repair this utility is executed.
	# See cache_check_executable how to obtain binaries.
	#
	# cache_repair_executable = "autodetect"

# Array of extra string options passed with cache_repair command.
	# cache_repair_options = [ "" ]

# Configuration option global/system_id_source.
	# The method LVM uses to set the local system ID.
	# Volume Groups can also be given a system ID (by vgcreate, vgchange,
	# or vgimport.) A VG on shared storage devices is accessible only to
	# the host with a matching system ID. See 'man lvmsystemid' for
	# information on limitations and correct usage.
	# 
	# Accepted values:
	#	none
	#	  The host has no system ID.
	#	lvmlocal
	#	  Obtain the system ID from the system_id setting in the 'local'
	#	  section of an lvm configuration file, e.g. lvmlocal.conf.
	#	uname
	#	  Set the system ID from the hostname (uname) of the system.
	#	  System IDs beginning localhost are not permitted.
	#	machineid
	#	  Use the contents of the machine-id file to set the system ID.
	#	  Some systems create this file at installation time.
	#	  See 'man machine-id' and global/etc.
	#	file
	#	  Use the contents of another file (system_id_file) to set the
	#	  system ID.
	# 
	system_id_source = "none"

# Configuration option global/system_id_file.
	# The full path to the file containing a system ID.
	# This is used when system_id_source is set to 'file'.
	# Comments starting with the character # are ignored.
	# This configuration option does not have a default value defined.

# Full path of the utility called to dump cache metadata content.
	# See cache_check_executable how to obtain binaries.
	#
	# cache_dump_executable = "autodetect"
}

activation {
	# Set to 1 to perform internal checks on the operations issued to
	# libdevmapper.  Useful for debugging problems with activation.
	# Some of the checks may be expensive, so it's best to use this
	# only when there seems to be a problem.
	checks = 0

# Set to 0 to disable udev synchronisation (if compiled into the binaries).
	# Processes will not wait for notification from udev.
	# They will continue irrespective of any possible udev processing
	# in the background.  You should only use this if udev is not running
	# or has rules that ignore the devices LVM2 creates.
	# The command line argument --nodevsync takes precedence over this setting.
	# If set to 1 when udev is not running, and there are LVM2 processes
	# waiting for udev, run 'dmsetup udevcomplete_all' manually to wake them up.
	udev_sync = 1

# Set to 0 to disable the udev rules installed by LVM2 (if built with
	# --enable-udev_rules). LVM2 will then manage the /dev nodes and symlinks
	# for active logical volumes directly itself.
	# N.B. Manual intervention may be required if this setting is changed
	# while any logical volumes are active.
	udev_rules = 1

# Set to 1 for LVM2 to verify operations performed by udev. This turns on
	# additional checks (and if necessary, repairs) on entries in the device
	# directory after udev has completed processing its events. 
	# Useful for diagnosing problems with LVM2/udev interactions.
	verify_udev_operations = 0

# If set to 1 and if deactivation of an LV fails, perhaps because
	# a process run from a quick udev rule temporarily opened the device,
	# retry the operation for a few seconds before failing.
	retry_deactivation = 1

# How to fill in missing stripes if activating an incomplete volume.
	# Using "error" will make inaccessible parts of the device return
	# I/O errors on access.  You can instead use a device path, in which 
	# case, that device will be used to in place of missing stripes.
	# But note that using anything other than "error" with mirrored 
	# or snapshotted volumes is likely to result in data corruption.
	missing_stripe_filler = "error"

# The linear target is an optimised version of the striped target
	# that only handles a single stripe.  Set this to 0 to disable this
	# optimisation and always use the striped target.
	use_linear_target = 1

# How much stack (in KB) to reserve for use while devices suspended
	# Prior to version 2.02.89 this used to be set to 256KB
	reserved_stack = 64

# How much memory (in KB) to reserve for use while devices suspended
	reserved_memory = 8192

# Nice value used while devices suspended
	process_priority = -18

# If volume_list is defined, each LV is only activated if there is a
	# match against the list.
	#
	#	"vgname" and "vgname/lvname" are matched exactly.
	#	"@tag" matches any tag set in the LV or VG.
	#	"@*" matches if any tag defined on the host is also set in the LV or VG
	#
	# If any host tags exist but volume_list is not defined, a default
	# single-entry list containing "@*" is assumed.
	#
	# volume_list = [ "vg1", "vg2/lvol1", "@tag1", "@*" ]

# If auto_activation_volume_list is defined, each LV that is to be
	# activated with the autoactivation option (--activate ay/-a ay) is
	# first checked against the list. There are two scenarios in which
	# the autoactivation option is used:
	#
	#	- automatic activation of volumes based on incoming PVs. If all the
	#	  PVs making up a VG are present in the system, the autoactivation
	#	  is triggered. This requires lvmetad (global/use_lvmetad=1) and udev
	#	  to be running. In this case, "pvscan --cache -aay" is called
	#	  automatically without any user intervention while processing
	#	  udev events. Please, make sure you define auto_activation_volume_list
	#	  properly so only the volumes you want and expect are autoactivated.
	#
	#	- direct activation on command line with the autoactivation option.
	#	  In this case, the user calls "vgchange --activate ay/-a ay" or
	#	  "lvchange --activate ay/-a ay" directly.
	#
	# By default, the auto_activation_volume_list is not defined and all
	# volumes will be activated either automatically or by using --activate ay/-a ay.
	#
	# N.B. The "activation/volume_list" is still honoured in all cases so even
	# if the VG/LV passes the auto_activation_volume_list, it still needs to
	# pass the volume_list for it to be activated in the end.

# If auto_activation_volume_list is defined but empty, no volumes will be
	# activated automatically and --activate ay/-a ay will do nothing.
	#
	# auto_activation_volume_list = []

# If auto_activation_volume_list is defined and it's not empty, only matching
	# volumes will be activated either automatically or by using --activate ay/-a ay.
	#
	#	"vgname" and "vgname/lvname" are matched exactly.
	#	"@tag" matches any tag set in the LV or VG.
	#	"@*" matches if any tag defined on the host is also set in the LV or VG
	#
	# auto_activation_volume_list = [ "vg1", "vg2/lvol1", "@tag1", "@*" ]

# If read_only_volume_list is defined, each LV that is to be activated 
	# is checked against the list, and if it matches, it as activated
	# in read-only mode.  (This overrides '--permission rw' stored in the
	# metadata.)
	#
	#	"vgname" and "vgname/lvname" are matched exactly.
	#	"@tag" matches any tag set in the LV or VG.
	#	"@*" matches if any tag defined on the host is also set in the LV or VG
	#
	# read_only_volume_list = [ "vg1", "vg2/lvol1", "@tag1", "@*" ]

# Each LV can have an 'activation skip' flag stored persistently against it.
	# During activation, this flag is used to decide whether such an LV is skipped.
	# The 'activation skip' flag can be set during LV creation and by default it
	# is automatically set for thin snapshot LVs. The 'auto_set_activation_skip'
	# enables or disables this automatic setting of the flag while LVs are created.
	# auto_set_activation_skip = 1

# For RAID or 'mirror' segment types, 'raid_region_size' is the
	# size (in KiB) of each:
	# - synchronization operation when initializing
	# - each copy operation when performing a 'pvmove' (using 'mirror' segtype)
	# This setting has replaced 'mirror_region_size' since version 2.02.99
	raid_region_size = 512

# Setting to use when there is no readahead value stored in the metadata.
	#
	# "none" - Disable readahead.
	# "auto" - Use default value chosen by kernel.
	readahead = "auto"

# 'raid_fault_policy' defines how a device failure in a RAID logical
	# volume is handled.  This includes logical volumes that have the following
	# segment types: raid1, raid4, raid5*, and raid6*.
	#
	# In the event of a failure, the following policies will determine what
	# actions are performed during the automated response to failures (when
	# dmeventd is monitoring the RAID logical volume) and when 'lvconvert' is
	# called manually with the options '--repair' and '--use-policies'.
	#
	# "warn"	- Use the system log to warn the user that a device in the RAID
	#		  logical volume has failed.  It is left to the user to run
	#		  'lvconvert --repair' manually to remove or replace the failed
	#		  device.  As long as the number of failed devices does not
	#		  exceed the redundancy of the logical volume (1 device for
	#		  raid4/5, 2 for raid6, etc) the logical volume will remain
	#		  usable.
	#
	# "allocate" - Attempt to use any extra physical volumes in the volume
	#		  group as spares and replace faulty devices.
	#
	raid_fault_policy = "warn"

# 'mirror_image_fault_policy' and 'mirror_log_fault_policy' define
	# how a device failure affecting a mirror (of "mirror" segment type) is
	# handled.	A mirror is composed of mirror images (copies) and a log.
	# A disk log ensures that a mirror does not need to be re-synced
	# (all copies made the same) every time a machine reboots or crashes.
	#
	# In the event of a failure, the specified policy will be used to determine
	# what happens. This applies to automatic repairs (when the mirror is being
	# monitored by dmeventd) and to manual lvconvert --repair when
	# --use-policies is given.
	#
	# "remove" - Simply remove the faulty device and run without it.  If
	#			 the log device fails, the mirror would convert to using
	#			 an in-memory log.	This means the mirror will not
	#			 remember its sync status across crashes/reboots and
	#			 the entire mirror will be re-synced.  If a
	#			 mirror image fails, the mirror will convert to a
	#			 non-mirrored device if there is only one remaining good
	#			 copy.
	#
	# "allocate" - Remove the faulty device and try to allocate space on
	#			 a new device to be a replacement for the failed device.
	#			 Using this policy for the log is fast and maintains the
	#			 ability to remember sync state through crashes/reboots.
	#			 Using this policy for a mirror device is slow, as it
	#			 requires the mirror to resynchronize the devices, but it
	#			 will preserve the mirror characteristic of the device.
	#			 This policy acts like "remove" if no suitable device and
	#			 space can be allocated for the replacement.
	#
	# "allocate_anywhere" - Not yet implemented. Useful to place the log device
	#			 temporarily on same physical volume as one of the mirror
	#			 images. This policy is not recommended for mirror devices
	#			 since it would break the redundant nature of the mirror. This
	#			 policy acts like "remove" if no suitable device and space can
	#			 be allocated for the replacement.
	mirror_log_fault_policy = "allocate"
	mirror_image_fault_policy = "remove"

# 'snapshot_autoextend_threshold' and 'snapshot_autoextend_percent' define
	# how to handle automatic snapshot extension. The former defines when the
	# snapshot should be extended: when its space usage exceeds this many
	# percent. The latter defines how much extra space should be allocated for
	# the snapshot, in percent of its current size.
	#
	# For example, if you set snapshot_autoextend_threshold to 70 and
	# snapshot_autoextend_percent to 20, whenever a snapshot exceeds 70% usage,
	# it will be extended by another 20%. For a 1G snapshot, using up 700M will
	# trigger a resize to 1.2G. When the usage exceeds 840M, the snapshot will
	# be extended to 1.44G, and so on.
	#
	# Setting snapshot_autoextend_threshold to 100 disables automatic
	# extensions. The minimum value is 50 (A setting below 50 will be treated
	# as 50).

snapshot_autoextend_threshold = 100
	snapshot_autoextend_percent = 20

# 'thin_pool_autoextend_threshold' and 'thin_pool_autoextend_percent' define
	# how to handle automatic pool extension. The former defines when the
	# pool should be extended: when its space usage exceeds this many
	# percent. The latter defines how much extra space should be allocated for
	# the pool, in percent of its current size.
	#
	# For example, if you set thin_pool_autoextend_threshold to 70 and
	# thin_pool_autoextend_percent to 20, whenever a pool exceeds 70% usage,
	# it will be extended by another 20%. For a 1G pool, using up 700M will
	# trigger a resize to 1.2G. When the usage exceeds 840M, the pool will
	# be extended to 1.44G, and so on.
	#
	# Setting thin_pool_autoextend_threshold to 100 disables automatic
	# extensions. The minimum value is 50 (A setting below 50 will be treated
	# as 50).

thin_pool_autoextend_threshold = 100
	thin_pool_autoextend_percent = 20

# While activating devices, I/O to devices being (re)configured is
	# suspended, and as a precaution against deadlocks, LVM2 needs to pin
	# any memory it is using so it is not paged out.  Groups of pages that
	# are known not to be accessed during activation need not be pinned
	# into memory.	Each string listed in this setting is compared against
	# each line in /proc/self/maps, and the pages corresponding to any
	# lines that match are not pinned.	On some systems locale-archive was
	# found to make up over 80% of the memory used by the process.
	# mlock_filter = [ "locale/locale-archive", "gconv/gconv-modules.cache" ]

# Set to 1 to revert to the default behaviour prior to version 2.02.62
	# which used mlockall() to pin the whole process's memory while activating
	# devices.
	use_mlockall = 0

# Monitoring is enabled by default when activating logical volumes.
	# Set to 0 to disable monitoring or use the --ignoremonitoring option.
	monitoring = 1

# When pvmove or lvconvert must wait for the kernel to finish
	# synchronising or merging data, they check and report progress
	# at intervals of this number of seconds.  The default is 15 seconds.
	# If this is set to 0 and there is only one thing to wait for, there
	# are no progress reports, but the process is awoken immediately the
	# operation is complete.
	polling_interval = 15

# 'activation_mode' determines how Logical Volumes are activated if
	# any devices are missing.	Possible settings are:
	#
	#	"complete" -  Only allow activation of an LV if all of the Physical
	#			  Volumes it uses are present.	Other PVs in the Volume
	#			  Group may be missing.
	#
	#	"degraded" -  Like "complete", but additionally RAID Logical Volumes of
	#			  segment type raid1, raid4, raid5, radid6 and raid10 will
	#			  be activated if there is no data loss, i.e. they have
	#			  sufficient redundancy to present the entire addressable
	#			  range of the Logical Volume.
	#
	#	"partial"  -  Allows the activation of any Logical Volume even if
	#			  a missing or failed PV could cause data loss with a
	#			  portion of the Logical Volume inaccessible.
	#			  This setting should not normally be used, but may
	#			  sometimes assist with data recovery.
	#
	# This setting was introduced in LVM version 2.02.108.	It corresponds
	# with the '--activationmode' option for lvchange and vgchange.
	activation_mode = "degraded"
}

# Report settings.
#
# report {
	# Align columns on report output.
	# aligned=1

# When buffered reporting is used, the report's content is appended
	# incrementally to include each object being reported until the report
	# is flushed to output which normally happens at the end of command
	# execution. Otherwise, if buffering is not used, each object is
	# reported as soon as its processing is finished.
	# buffered=1

# Show headings for columns on report.
	# headings=1

# A separator to use on report after each field.
	# separator=" "

# A separator to use for list items when reported.
	# list_item_separator=","

# Use a field name prefix for each field reported.
	# prefixes=0

# Quote field values when using field name prefixes.
	# quoted=1

# Output each column as a row. If set, this also implies report/prefixes=1.
	# colums_as_rows=0

# Use binary values "0" or "1" instead of descriptive literal values for
	# columns that have exactly two valid values to report (not counting the
	# "unknown" value which denotes that the value could not be determined).
	#
	# binary_values_as_numeric = 0

# Comma separated list of columns to sort by when reporting 'lvm devtypes' command.
	# See 'lvm devtypes -o help' for the list of possible fields.
	# devtypes_sort="devtype_name"

# Comma separated list of columns to report for 'lvm devtypes' command.
	# See 'lvm devtypes -o help' for the list of possible fields.
	# devtypes_cols="devtype_name,devtype_max_partitions,devtype_description"

# Comma separated list of columns to report for 'lvm devtypes' command in verbose mode.
	# See 'lvm devtypes -o help' for the list of possible fields.
	# devtypes_cols_verbose="devtype_name,devtype_max_partitions,devtype_description"

# Comma separated list of columns to sort by when reporting 'lvs' command.
	# See 'lvs -o help' for the list of possible fields.
	# lvs_sort="vg_name,lv_name"

# Comma separated list of columns to report for 'lvs' command.
	# See 'lvs -o help' for the list of possible fields.
	# lvs_cols="lv_name,vg_name,lv_attr,lv_size,pool_lv,origin,data_percent,metadata_percent,move_pv,mirror_log,copy_percent,convert_lv"

# Comma separated list of columns to report for 'lvs' command in verbose mode.
	# See 'lvs -o help' for the list of possible fields.
	# lvs_cols_verbose="lv_name,vg_name,seg_count,lv_attr,lv_size,lv_major,lv_minor,lv_kernel_major,lv_kernel_minor,pool_lv,origin,data_percent,metadata_percent,move_pv,copy_percent,mirror_log,convert

# Comma separated list of columns to sort by when reporting 'vgs' command.
	# See 'vgs -o help' for the list of possible fields.
	# vgs_sort="vg_name"

# Comma separated list of columns to report for 'vgs' command.
	# See 'vgs -o help' for the list of possible fields.
	# vgs_cols="vg_name,pv_count,lv_count,snap_count,vg_attr,vg_size,vg_free"

# Comma separated list of columns to report for 'vgs' command in verbose mode.
	# See 'vgs -o help' for the list of possible fields.
	# vgs_cols_verbose="vg_name,vg_attr,vg_extent_size,pv_count,lv_count,snap_count,vg_size,vg_free,vg_uuid,vg_profile"

# Comma separated list of columns to sort by when reporting 'pvs' command.
	# See 'pvs -o help' for the list of possible fields.
	# pvs_sort="pv_name"

# Comma separated list of columns to report for 'pvs' command.
	# See 'pvs -o help' for the list of possible fields.
	# pvs_cols="pv_name,vg_name,pv_fmt,pv_attr,pv_size,pv_free"

# Comma separated list of columns to report for 'pvs' command in verbose mode.
	# See 'pvs -o help' for the list of possible fields.
	# pvs_cols_verbose="pv_name,vg_name,pv_fmt,pv_attr,pv_size,pv_free,dev_size,pv_uuid"

# Comma separated list of columns to sort by when reporting 'lvs --segments' command.
	# See 'lvs --segments -o help' for the list of possible fields.
	# segs_sort="vg_name,lv_name,seg_start"

# Comma separated list of columns to report for 'lvs --segments' command.
	# See 'lvs --segments  -o help' for the list of possible fields.
	# segs_cols="lv_name,vg_name,lv_attr,stripes,segtype,seg_size"

# Comma separated list of columns to report for 'lvs --segments' command in verbose mode.
	# See 'lvs --segments -o help' for the list of possible fields.
	# segs_cols_verbose="lv_name,vg_name,lv_attr,seg_start,seg_size,stripes,segtype,stripesize,chunksize"

# Comma separated list of columns to sort by when reporting 'pvs --segments' command.
	# See 'pvs --segments -o help' for the list of possible fields.
	# pvsegs_sort="pv_name,pvseg_start"

# Comma separated list of columns to sort by when reporting 'pvs --segments' command.
	# See 'pvs --segments -o help' for the list of possible fields.
	# pvsegs_cols="pv_name,vg_name,pv_fmt,pv_attr,pv_size,pv_free,pvseg_start,pvseg_size"

# Comma separated list of columns to sort by when reporting 'pvs --segments' command in verbose mode.
	# See 'pvs --segments -o help' for the list of possible fields.
	# pvsegs_cols_verbose="pv_name,vg_name,pv_fmt,pv_attr,pv_size,pv_free,pvseg_start,pvseg_size,lv_name,seg_start_pe,segtype,seg_pe_ranges"
#}

####################
# Advanced section #
####################

# Metadata settings
#
# metadata {
        # Configuration option metadata/check_pv_device_sizes.
        # Check device sizes are not smaller than corresponding PV sizes.
        # If device size is less than corresponding PV size found in metadata,
        # there is always a risk of data loss. If this option is set, then LVM
        # issues a warning message each time it finds that the device size is
        # less than corresponding PV size. You should not disable this unless
        # you are absolutely sure about what you are doing!
        # This configuration option is advanced.
        # This configuration option has an automatic default value.
        # check_pv_device_sizes = 1

# Configuration option metadata/pvmetadatacopies.
        # Number of copies of metadata to store on each PV.
        # Possible options are: 0, 1, 2.
        # If set to 2, two copies of the VG metadata are stored on
        # the PV, one at the front of the PV, and one at the end.
        # If set to 1, one copy is stored at the front of the PV.
        # If set to 0, no copies are stored on the PV. This may
        # be useful with VGs containing large numbers of PVs.
        # The '--pvmetadatacopies' option overrides this setting.
        # This configuration option is advanced.
        # pvmetadatacopies = 1

# Default number of copies of metadata to maintain for each VG.
	# If set to a non-zero value, LVM automatically chooses which of
	# the available metadata areas to use to achieve the requested
	# number of copies of the VG metadata.	If you set a value larger
	# than the the total number of metadata areas available then
	# metadata is stored in them all.
	# The default value of 0 ("unmanaged") disables this automatic
	# management and allows you to control which metadata areas
	# are used at the individual PV level using 'pvchange
	# --metadataignore y/n'.

# vgmetadatacopies = 0

# Approximate default size of on-disk metadata areas in sectors.
	# You should increase this if you have large volume groups or
	# you want to retain a large on-disk history of your metadata changes.

# pvmetadatasize = 255

# List of directories holding live copies of text format metadata.
	# These directories must not be on logical volumes!
	# It's possible to use LVM2 with a couple of directories here,
	# preferably on different (non-LV) filesystems, and with no other 
	# on-disk metadata (pvmetadatacopies = 0). Or this can be in
	# addition to on-disk metadata areas.
	# The feature was originally added to simplify testing and is not
	# supported under low memory situations - the machine could lock up.
	#
	# Never edit any files in these directories by hand unless you
	# you are absolutely sure you know what you are doing! Use
	# the supplied toolset to make changes (e.g. vgcfgrestore).

# dirs = [ "/etc/lvm/metadata", "/mnt/disk2/lvm/metadata2" ]
#}

# Event daemon
#
dmeventd {
	# mirror_library is the library used when monitoring a mirror device.
	#
	# "libdevmapper-event-lvm2mirror.so" attempts to recover from
	# failures.  It removes failed devices from a volume group and
	# reconfigures a mirror as necessary. If no mirror library is
	# provided, mirrors are not monitored through dmeventd.

mirror_library = "libdevmapper-event-lvm2mirror.so"

# snapshot_library is the library used when monitoring a snapshot device.
	#
	# "libdevmapper-event-lvm2snapshot.so" monitors the filling of
	# snapshots and emits a warning through syslog when the use of
	# the snapshot exceeds 80%. The warning is repeated when 85%, 90% and
	# 95% of the snapshot is filled.

snapshot_library = "libdevmapper-event-lvm2snapshot.so"

# thin_library is the library used when monitoring a thin device.
	#
	# "libdevmapper-event-lvm2thin.so" monitors the filling of
	# pool and emits a warning through syslog when the use of
	# the pool exceeds 80%. The warning is repeated when 85%, 90% and
	# 95% of the pool is filled.

thin_library = "libdevmapper-event-lvm2thin.so"

# Full path of the dmeventd binary.
	#
	# executable = ""
}

Places

File lvm.conf of Package lvm2-clvm (Revision ea5a4ff2e9449564cce87fa2bce8e4b2)

Places