File setserial.init of Package setserial

Overview Repositories Revisions Requests Users Attributes Meta

File setserial.init of Package setserial (Revision 569e0838889986ad7f799856d1dce491)

Currently displaying revision 569e0838889986ad7f799856d1dce491 , Show latest

#!/bin/sh
#
# /etc/init.d/serial 
#
# Initializes the serial ports on your system
#
# Without uncommenting some of the lines in this script, you'll be unable to
# use ports other than the first two, and those only if they use "standard"
# IRQ values (whatever those are... :^)  The rc.serial script made a couple
# machines I tested this on hang at this point in the boot process, so it's
# commented out by default. However, if you need to set up extended serial
# ports, it's a very good starting point. It usually works great.
# More info that will be useful: I did some testing and found that the lines
# in /etc/rc.d/rc.serial that are most likely to make the machine hang are the
# one that sets up /dev/ttyS3, and the last time, which causes a report to be
# issued to the console about how the ports were configured. This tries to
# report on *every* port... if you change it so it only lists the ports you're
# going to use (/dev/ttyS0 /dev/cua1 /dev/cua2 for example) that it probably
# won't cause a hang. Also, the "wild" interrupt detection used for auto-
# configuration can cause problems as well. I highly recommend using the
# manual configuration lines to avoid trouble.
#
### BEGIN INIT INFO
# Provides:          setserial
# Should-Start:      $local_fs boot.loadmodules
# Should-Stop:	     $null
# Required-Start:
# Required-Stop:
# Default-Start:     B
# Default-Stop:
# Description:       Initializes the serial ports
### END INIT INFO

. /etc/rc.status

SETSERIAL="/bin/setserial -b"

rc_reset
case $1 in
  start|b)
    PORTS=`(for p in /dev/ttyS*; do isserial <$p && echo $p; done) 2>/dev/null`

run_setserial ()
    {
	$SETSERIAL $@
	rc_status
    }

echo "Configuring serial ports..."

# Do wild interrupt detection (uncomment if you're brave enough to
    # attempt auto-configuration... )
    #
    # run_setserial -W ${PORTS}

###############################################################
    #
    # AUTOMATIC CONFIGURATION 
    #
    # Uncomment the appropriate lines below to enable auto-configuration
    # of a particular board.  Or comment them out to disable them....
    #
    ###############################################################

# Do AUTOMATIC_IRQ probing
    #
    AUTO_IRQ=auto_irq

# These are the standard COM1 through COM4 devices
    #
    # If you have an internal modeme with a Rockwell Chipset, add a "skip_test"
    # to the /dev/ttyS3 line below.  (It's not added by default because it will
    # screw up people with 8514 displays).
    #
    # run_setserial /dev/ttyS0 ${AUTO_IRQ} skip_test autoconfig
    # run_setserial /dev/ttyS1 ${AUTO_IRQ} skip_test autoconfig
    # run_setserial /dev/ttyS2 ${AUTO_IRQ} skip_test autoconfig
    # run_setserial /dev/ttyS3 ${AUTO_IRQ} autoconfig

# These are for the first AST Fourport board (base address 0x1A0)
    #
    # run_setserial /dev/ttyS4 ${AUTO_IRQ} autoconfig
    # run_setserial /dev/ttyS5 ${AUTO_IRQ} autoconfig
    # run_setserial /dev/ttyS6 ${AUTO_IRQ} autoconfig
    # run_setserial /dev/ttyS7 ${AUTO_IRQ} autoconfig

# These are for the second AST Fourport board (base address 0x2A0)
    #
    # run_setserial /dev/ttyS8 ${AUTO_IRQ} autoconfig
    # run_setserial /dev/ttyS9 ${AUTO_IRQ} autoconfig
    # run_setserial /dev/ttyS10 ${AUTO_IRQ} autoconfig
    # run_setserial /dev/ttyS11 ${AUTO_IRQ} autoconfig

# These are the 3rd and 4th ports on the Accent Async board.
    #
    # run_setserial /dev/ttyS12 ${AUTO_IRQ} autoconfig
    # run_setserial /dev/ttyS13 ${AUTO_IRQ} autoconfig
 
    # Usenet Serial Board II (base address 0x100)
    #
    # run_setserial /dev/ttyS16 ${AUTO_IRQ} autoconfig
    # run_setserial /dev/ttyS17 ${AUTO_IRQ} autoconfig
    # run_setserial /dev/ttyS18 ${AUTO_IRQ} autoconfig
    # run_setserial /dev/ttyS19 ${AUTO_IRQ} autoconfig

# BocaBoard 4 port (BB-1004) (base address 0x100)
    # 
    # run_setserial /dev/ttyS16 ${AUTO_IRQ} autoconfig
    # run_setserial /dev/ttyS17 ${AUTO_IRQ} autoconfig
    # run_setserial /dev/ttyS18 ${AUTO_IRQ} autoconfig
    # run_setserial /dev/ttyS19 ${AUTO_IRQ} autoconfig

# BocaBoard 8 port (BB-1008) (base address 0x100),
    # or two BB-1004's (base addresses 0x100 and 0x120)
    #
    # run_setserial /dev/ttyS16 ${AUTO_IRQ} autoconfig
    # run_setserial /dev/ttyS17 ${AUTO_IRQ} autoconfig
    # run_setserial /dev/ttyS18 ${AUTO_IRQ} autoconfig
    # run_setserial /dev/ttyS19 ${AUTO_IRQ} autoconfig
    # run_setserial /dev/ttyS20 ${AUTO_IRQ} autoconfig
    # run_setserial /dev/ttyS21 ${AUTO_IRQ} autoconfig
    # run_setserial /dev/ttyS22 ${AUTO_IRQ} autoconfig
    # run_setserial /dev/ttyS23 ${AUTO_IRQ} autoconfig

# BocaBoard 16 port (BB-1008), (base address 0x100),
    # or two BB-1008's (base addresses 0x100 and 0x140),
    # or four BB-1004's (base address 0x100, 0x120, 0x140, and 0x160)
    #
    # Warning --- some of these ports may conflict with the Future Domain
    # SCSI controller.  If you want to run both the BocaBoards and the 
    # Future Domain controller, you may need to change the port assignment
    # of the Bocaboards -- see below in the section on manual configuration.
    #
    # run_setserial /dev/ttyS16 ${AUTO_IRQ} autoconfig
    # run_setserial /dev/ttyS17 ${AUTO_IRQ} autoconfig
    # run_setserial /dev/ttyS18 ${AUTO_IRQ} autoconfig
    # run_setserial /dev/ttyS19 ${AUTO_IRQ} autoconfig
    # run_setserial /dev/ttyS20 ${AUTO_IRQ} autoconfig
    # run_setserial /dev/ttyS21 ${AUTO_IRQ} autoconfig
    # run_setserial /dev/ttyS22 ${AUTO_IRQ} autoconfig
    # run_setserial /dev/ttyS23 ${AUTO_IRQ} autoconfig
    # run_setserial /dev/ttyS24 ${AUTO_IRQ} autoconfig
    # run_setserial /dev/ttyS25 ${AUTO_IRQ} autoconfig
    # run_setserial /dev/ttyS26 ${AUTO_IRQ} autoconfig
    # run_setserial /dev/ttyS27 ${AUTO_IRQ} autoconfig
    # run_setserial /dev/ttyS28 ${AUTO_IRQ} autoconfig
    # run_setserial /dev/ttyS29 ${AUTO_IRQ} autoconfig
    # run_setserial /dev/ttyS30 ${AUTO_IRQ} autoconfig
    # run_setserial /dev/ttyS31 ${AUTO_IRQ} autoconfig

###############################################################
    #
    # MANUAL CONFIGURATION 
    #
    # If you want to do manual configuration of one or more of your 
    # serial ports, uncomment and modify the relevant lines.
    #
    ###############################################################

# These are the standard COM1 through COM4 devices
    #
    # run_setserial /dev/ttyS0 uart 16550A port 0x3F8 irq 4
    # run_setserial /dev/ttyS1 uart 16550A port 0x2F8 irq 3
    # run_setserial /dev/ttyS2 uart 16450 port 0x3E8 irq 4
    # run_setserial /dev/ttyS3 uart 16450 port 0x2E8 irq 3
    
    # These are the first set of AST Fourport ports
    #
    # run_setserial /dev/ttyS4 uart 16450 port 0x2A0 irq 7 fourport
    # run_setserial /dev/ttyS5 uart 16450 port 0x2A8 irq 7 fourport
    # run_setserial /dev/ttyS6 uart 16450 port 0x2B0 irq 7 fourport
    # run_setserial /dev/ttyS7 uart 16450 port 0x2B8 irq 7 fourport
    
    # These are the second set of AST Fourport ports
    #
    # run_setserial /dev/ttyS8 uart 16450 port 0x2A0 irq 5 fourport
    # run_setserial /dev/ttyS9 uart 16450 port 0x2A8 irq 5 fourport
    # run_setserial /dev/ttyS10 uart 16450 port 0x2B0 irq 5 fourport
    # run_setserial /dev/ttyS11 uart 16450 port 0x2B8 irq 5 fourport

# These are the 3rd and 4th ports on the Accent Async board.
    #
    # run_setserial /dev/ttyS12 uart 16450 port 0x330 irq 4
    # run_setserial /dev/ttyS13 uart 16450 port 0x338 irq 4
    
    # These are two spare devices you can use to customize for 
    # some board which is not supported above....
    # run_setserial /dev/ttyS14 uart XXXXX port XXXX irq X
    # run_setserial /dev/ttyS15 uart XXXXX port XXXX irq X
    
    # These are the ports used for either the Usenet Serial II
    # board, or the Boca Board 4, 8, or 16 port boards.
    #
    # Uncomment only the first 4 lines for the Usenet Serial II board,
    # and uncomment the first 4, 8, or all 16 lines for the
    # Boca Board BB-1004, BB-1008, and BB-2016 respectively.
    #
    # run_setserial /dev/ttyS16 uart 16550A port 0x100 irq 12
    # run_setserial /dev/ttyS17 uart 16550A port 0x108 irq 12
    # run_setserial /dev/ttyS18 uart 16550A port 0x110 irq 12
    # run_setserial /dev/ttyS19 uart 16550A port 0x118 irq 12
    # run_setserial /dev/ttyS20 uart 16550A port 0x120 irq 12
    # run_setserial /dev/ttyS21 uart 16550A port 0x128 irq 12
    # run_setserial /dev/ttyS22 uart 16550A port 0x130 irq 12
    # run_setserial /dev/ttyS23 uart 16550A port 0x138 irq 12
    # run_setserial /dev/ttyS24 uart 16550A port 0x140 irq 12
    # run_setserial /dev/ttyS25 uart 16550A port 0x148 irq 12
    # run_setserial /dev/ttyS26 uart 16550A port 0x150 irq 12
    # run_setserial /dev/ttyS27 uart 16550A port 0x158 irq 12
    # run_setserial /dev/ttyS28 uart 16550A port 0x160 irq 12
    # run_setserial /dev/ttyS29 uart 16550A port 0x168 irq 12
    # run_setserial /dev/ttyS30 uart 16550A port 0x170 irq 12
    # run_setserial /dev/ttyS31 uart 16550A port 0x178 irq 12
    
    ###########################################################
    #
    # Print the results of the serial configuration process
    #
    ###########################################################

${SETSERIAL} -bg ${PORTS}
    rc_status
    echo "Configured serial ports"
    rc_status -v1
    ;;
  stop)
    # skip / do nothing
    ;;
  status)
    PORTS=`(for p in /dev/ttyS*; do isserial <$p && echo $p; done) 2>/dev/null`
    ${SETSERIAL} -bg ${PORTS}
    rc_status -v1
    ;;
  *)
    echo "usage: setserial {start|stop|status}"
    ;;
esac
rc_exit

Places

File setserial.init of Package setserial (Revision 569e0838889986ad7f799856d1dce491)

Places