openSUSE Build Service

Overview Repositories Revisions Requests Users Attributes Meta

File sdparm.changes of Package sdparm

-------------------------------------------------------------------
Wed Oct 23 15:33:48 UTC 2013 - p.drouand@gmail.com

- Remove %fillup_prereq and %insserv_prereq; package doesn't provide
  any sysvinit script

-------------------------------------------------------------------
Thu Jun 13 13:56:56 UTC 2013 - jengelh@inai.de

- Update to new upstream release 1.08
* New utilities: scsi_ch_swp, sas_disk_blink
* Tracked changes at t10.org since January 2012:
* device id VPD: add protocol specific port identifier
* control extension mpage: add max sense data length
* power condition mpage: FIDCPC->CCF_IDLE, FSBCPC->CCF_STAND,
  FSTCPC->CCF_STOPP (spc4r34+)
* caching mpage: add SYNC_PROG field (sbc3r33)
* block device characteristics VPD page additions sbc3r34
* extended inquiry vpd page: add max supported sense data length
* protocol-specific port information VPD page for SAS SSP,
  persistent connection (spl3r2), power disable (spl3r3)
* allow --readonly with --set= and --clear=
* add placeholder for third party copy VPD page
* supply more information if a UA occurs
- Normalized install procedure
- Build with libsgutils support

-------------------------------------------------------------------
Sun Apr 22 11:46:53 UTC 2012 - puzel@suse.com

- Update to version 1.07 
  - LB provisioning + Block limits VPD pages to sbc3r27
  - Enhanced phy control page: optical mode enabled (spl-r07)
  - Phy control and discover page: sync to spl2r02
  - sync with spc4r31+32 (handle status good with sense)
  - extented inquiry VPD: add POA_SUP, HRA_SUP and VSA_SUP
  - application tag mode page subcode 0xf0->0x2 (sbc3r28)
  - add 'sinq' pseudo VPD page for standard inquiry response
  - add power consumption mode and VPD pages (spc4r33)
  - point out some mode page numbers are vendor specific

-------------------------------------------------------------------
Tue May 24 17:31:45 CEST 2011 - dimstar@opensuse.org

- Update to version 1.06:
  + allow upper and lower case in field, (mode and vpd) page,
    vendor, transport or command matching
  + control mode page: add ATMPE and RWWP fields (spc4r27)
  + extended inquiry vpd page: add extended self test completion
    minutes field (spc4r27)
  + power control mode page: PM_BG_PRECEDENCE field (spc4r24)
    - FIDCPC, FSBCPC, FSTCPC fields (spc4r25)
  + sbc3r25 renames 'thin' provisioning' to 'logical block
    provisioning'; changes mode+vpd page and field names
    - add Application tag mode page
    - add SITPUA bit to logical block provisioning mode page
  + fix '-eal' problem with vendor pages
  + point svn:externals to rev 334 of sg3_utils

-------------------------------------------------------------------
Fri Aug 13 11:56:39 CEST 2010 - dimstar@opensuse.org

- Update to version 1.05:
  + add '--readonly' option especially for '-C start' and
    '-C stop' on ATA disks.
  + Control mode page updates (spc4r23)
  + add Control data protection mode page (ssc4r01)
  + block device characteristics VPD page: decode form factor
  + extended inquiry VPD page: activate_microcode+r_sup (spc4r23)
  + Automation device serial number and Data transfer device
    element address VPD pages (ssc4r01)
  + add SBC Referrals VPD page (sbc3r22)
  + expand SBC Thin provisioning VPD page (sbc3r22)
  + expand SBC Block limits VPD page (sbc3r22)
  + SAS-2.1 specification split, upper layers placed in SPL
    - add enable_slumber and enable_partial fields to
      Enhanced phy control mode page
  + add AM_MAINTAINER_MODE to configure.ac to lessen build issues
  + build infrastructure change to use libsgutils2 if available
- Changes from version 1.04:
  + add SAT ATA Power condition mode page (sat2r06)
  + add SBC Thin provisioning mode page (sbc3r20)
  + add SBC Thin provisioning VPD page (sbc3r20)
  + sync with spc4r21
  + add Power condition, update extended inquiry VPD pages
  + smc3: add Device capabilities + Extended device
    capabilities + Transport geometry parameters mode pages
  + prepare for Thin provisioning VPD and mode pages
  + expand block limits VPD page
  + update Power condition mode page
  + rename SAS-2 phy mode page to Enhanced phy control (SAS)
  + add ADC mode (sub)page place holders
  + print mode page descriptors in full in more contexts
  + add linux bsg support
  + scripts/sas_disk_blink: moved here from sg3_utils package
  + rework the '-w' option (win32) per sg_scan in sg3_utils
  + change SDPARM_* constants to SG_LIB_*
  + remove sdparm.html, refer to its url in sdparm.8
  + sdparm.spec: correction to configure call

-------------------------------------------------------------------
Tue Aug 12 18:40:54 CEST 2008 - garloff@suse.de

- Update to sdparm-1.03:
  * supports more than one device on command linx
  * speed[=val] and profile commands for MMC
  * Extended Inquiry VPD page updated (spc4r15)
  * SAS protocol-specific port mpage (add CAWT, RTOL)
  * minor cleanups

-------------------------------------------------------------------
Fri May 23 10:11:29 CEST 2008 - hare@suse.de

- Using 'Provides' keyword to clean update dependency.

-------------------------------------------------------------------
Thu Apr 24 14:51:23 CEST 2008 - hare@suse.de

- Split off from the original scsi package.

Places

File sdparm.changes of Package sdparm

Places